Velocity XL RG KitClick here to purchase or contact the seller of this item on eBay |
||
Current Price: 12,000.00 USD |
You are bidding on a Velocity XL RG kit. Kit value from the factory is around $56K. It appears that the wings will need to be re skinned on the top of the wing, otherwise there hasn't been that much work done to the kit. A good composite person should be able to correct the wing skins, otherwise you can purchase new foam cores from the factory or have someone who works with composites cut new ones for you. For more information that comes with the kit, check Velocity's website. Retractable landing gear alone is a $9,000 option from the factory. This is a 200+ knot aircraft and includes the following (factory support is $800 from the factory):
The Velocity kit is constructed with the finest quality materials
available. The resins and fabrics are supplied by the leaders in the
aerospace industry. Most all hardware, metals, parts and fabrications
are certified aircraft quality. Because materials invested in the
construction of your kit are so important, you simply get the BEST.
Instructions and assistance consist of:
- A step-by-step Builder's Construction Manual, customized to one of the five various Velocity models
- an Owner's Flight Manual
- a set of DVD's which follow the construction of a standard Velocity from start through flight testing (over 20 hours total)
- "Velocity Online" Velocity's quarterly newsletter
- Velocity's "Builders Page" .
- Take a look and see the services we offer online. We have an online manual, construction photo gallery , links to other Velocity builders websites and much more.
- Factory Support through email or the phone.
Components Supplied in the Basic Velocity Kit
Foam Cores:
All foam cores are pre-cut, with level lines in place for proper alignment.- WING CORES: (SE) 2 leading edge, 3 trailing edge; (XL) 3 leading edge, 4 trailing edge
- CANARD CORES: (SE); (XL) 2 leading edge, 2 trailing edge
- ELEVATORS: 2
- AILERONS: 2
Spar Sections:
All spars are match-drilled, and have the bolt hole bushings already installed.- MAIN WING SPAR: 2 pre-molded
- CARRY-THROUGH (center section) SPAR: 1 pre-molded
- CANARD SPAR: 1 pre-molded
Fuel Strakes:
- 2 upper/2 lower foam-cored vacuum bagged.
- Skins finished in white primer
Fuselage:
- UPPER HALF: Foam core vacuum bagged composite shell. White epoxy primed and pre-marked for all cutouts. Upper cowl attached.
- LOWER HALF: Foam core vacuum bagged composite shell. White epoxy primed and pre-marked for all cut-outs. Lower cowl attached.
Hardware
AN hardware: nuts, bolts, screws, washers, hinges, pulleys, and cables to complete airframe- All pre-machined parts for complete control, brake, trim, and door systems (no welding or machining necessary)
- Hinges for canard-elevator assembly. All Mil-spec hinges for ailerons, rudders and door
- Electrical actuators and related parts for trim
- Master cylinders, brake lines, and heavy duty brakes
- (SE) 2 - 15 x 6.00-6 low profile main tires/tubes 1 - 340 x 5.00 nose wheel tire/tube; (XL) 2 - 6.00 x 6, 6 ply tires and tubes, 1 - 5.00 x 5, 6 ply tire and tube
- Seat hinges and front seat rails
- Rear seat rails (XL)
- 2 - 15 x 6.00-6 low profile main tires/tubes
- (RG)
- 1 - 340 x 5.00 nose wheel tire/tube (RG)
- Fiberglass cloth, epoxy resin, foam. Supply of application brushes, fillers, and mixing sticks
- 2 extruded aluminum I-beam straightedges (wing/canard construction)
Landing Gear:
- FIXED MAINS: 1 piece pre-molded S-fiberglass
- RETRACT MAINS: 2 piece premolded S-fiberglass
- NOSE GEAR: 1-1/4” 4130 steel tube. Assembled with all hardware for installation into airframe
Molded Parts:
All Fiberglass pre-molded:- (Fixed) wheel pants: 2 Mains / 1 Nose
- (Retract) nose gear doors, main gear doors
- 2-Air inlet scoops
- 2-Main gear saddle
- 4-Composite seat backs and headrests
- 4-Composite seat bottoms
- 1-Center keel
- 2-Wiring ducts
- 2-Canard tips
- 1-Fuel sump tank / fuel sump tank cover
- 1-Canard bulkhead
- 1-Firewall
- 1-Gear bulkhead
- 1-Instrument panel
- 1-Glare shield
- 2-Lower winglet extensions
- 4-Wing root ribs
- 2-NACA engine cooling inlet scoops
- 1-Landing light housing and lens
Windows:
- Pre-formed. One piece 1/4” plexiglass
- windshield, 2 front door/2 rear 1/8” plexiglass windows. All glass is medium tint.
Click here to purchase or contact the seller of this item on eBay